I have a problem with my Heat Wagon or Sure Flame heater. Who
should I contact for service?
Please click here for a list of authorized dealers in
your area. They will be happy to assist you with your heating
needs.
How do I contact my local Heat Wagon dealer?
Please click here for a list of authorized Heat Wagon dealers
in your area. Dealers are listed by state.
Is my Heat Wagon or Sure Flame heater CSA or MEA approved?
Please click on the model number’s link. You will see
the CSA or MEA approval seal for each heater. Click on those
seals to view each approval.
Can I use locally obtainable components to set up or service my Heat
Wagon or Sure Flame heater?
OEM components should always be used in any repair or set up situation. Only
OEM components are tested and approved by Heat Wagon engineers as
well as independent approval services. Non-OEM components may
affect how the heater performs and can cause heater failure or personal
injury. Non-OEM components will void factory warranty.
How do I know what size heater I need for the job?
You can use a formula that will roughly determine your BTU needs. The
formula is:
(Cubic Feet)(.133)( Desired Temperature Rise) = BTU Needed
| For example: |
Building A |
| Length |
100’ |
| Width |
50’ |
| Height |
20’ |
100’ x 50’= 5,000 square feet, multiply that by 20’ (ceilings),
and you have 100,000 cubic feet. If you want to raise the building
temperature by 50 degrees, then your formula will be as follows:
(100,000)(.133)(50) = 665,000 BTU’s
Given the BTUs needed, (2) S405 or (2) VG400 models are adequate.
What type of Heat Wagon or Sure Flame heater will best suit my needs?
Heat Wagon makes a variety of heaters including electric, oil fired, propane, and natural gas. These heaters can be direct fired or indirect fired. They are also available in 120 volt models as well as 240 volt single or three phase models and 480 volt three phase.
Are Heat Wagon or Sure Flame heaters available for rental?
Yes! Please refer to your local Heat Wagon dealer for pricing and availability.
Does Heat Wagon offer training on heaters and job sizing?
Yes, Heat Wagon dealers are trained on the technical aspects of Heat Wagon heaters as well as on how to properly size your specific needs.
Where is Heat Wagon located?
Heat Wagon is located in Valparaiso, IN just off the intersection
of State Highway 2 and County Road 400 East. The address is 342 N CR 400 E.
From the North:
Follow Highway 49 south and take Highway 2 east. Just after you
cross the railroad tracks, you’ll pass a school on the left. Turn
right onto CR 400 E. Heat Wagon is 1/10 of a mile on your right.
From the South:
(If north-bound on I65)
Follow Highway 30 east and take Highway 49 north to Highway 2 east. Just
after you cross the railroad tracks, you’ll pass a school on the
left. Turn right onto CR 400 E. Heat Wagon is 1/10 of a mile
on your right.
(If north-bound on Highway 49)
Take Highway 49 north to Highway 2 east. Just after you cross the
railroad tracks, you’ll pass a school on the left. Turn right
onto CR 400 E. Heat Wagon is 1/10 of a mile on your right.
From the West:
Follow Highway 30 east and take Highway 49 north to Highway 2 east. Just
after you cross the railroad tracks, you’ll pass a school on the
left. Turn right onto CR 400 E. Heat Wagon is 1/10 of a mile
on your right.
From the East:
Follow Highway 30 west and take Highway 49 north to Highway 2 east. Just
after you cross the railroad tracks, you’ll pass a school on the
left. Turn right onto CR 400 E. Heat Wagon is 1/10 of a mile
on your right.
What are the operating hours for Heat Wagon?
Heat Wagon is open from 8:00AM to 5:00PM Monday – Friday.
About Us | Our Products | Online Quote | Locate A Dealer | Applications
Training & Education | Product Manuals | Part Breakdowns | News & Events | FAQ
Customer Resource Center | Online Inquiry | Contact Us | Home
|
